一、删除Unit 1管理单元堆叠配置
适用于member 1的交换机，如果member不为1，还要执行switch 2 renumber 1这条命令，可参见删除unit 2交换机堆叠配置
console#show stack-port 查看堆叠接口
Configured Running
Stack Stack Link Link
Unit Interface Mode Mode Status Speed (Gb/s)
---- ---------------- ---------- ---------- ------------ ------------
1 xg1 Stack Stack Link Down 12
1 xg2 Stack Stack Link Up 12
1 xg3 Ethernet Ethernet Link Down Unknown
1 xg4 Ethernet Ethernet Link Down Unknown
2 xg1 Stack Stack Link Up 12
2 xg2 Stack Stack Link Down 12
2 xg3 Ethernet Ethernet Link Down Unknown
2 xg4 Ethernet Ethernet Link Down Unknown
console#show run 查看堆叠配置
!Current Configuration:
!System Description "PowerConnect 6224, 3.3.2.3, VxWorks 6.5"
!System Software Version 3.3.2.3
!Cut-through mode is configured as disabled
!
configure
stack
member 1 1
member 2 2
exit
switch 1 priority 12
switch 2 priority 11
ip address dhcp
exit
console#configure
console(config)#stack
console(config-stack)#stack-port 1/xg1 ethernet 恢复堆叠接口为以太网口
console(config-stack)#stack-port 1/xg2 ethernet
console(config-stack)#stack-port 2/xg1 ethernet
console(config-stack)#stack-port 2/xg2 ethernet
console(config-stack)#exit
console(config)#no switch 2 priority 删除堆叠优先级
console(config)#no switch 1 priority
console(config)#exit
console#copy runn start 保存配置，然后重启交换机
console#show switch 现在只有一台交换机了
Management Standby Preconfig Plugged-in Switch Code
SW Status Status Model ID Model ID Status Version
--- ---------- --------- ------------- ------------- ------------- -----------
1 Mgmt Sw PCT6224 PCT6224 OK 3.3.2.3
console#show stack-standby 堆叠相关配置没有了
Standby unit: None
console#show run
!Current Configuration:
!System Description "PowerConnect 6224, 3.3.2.3, VxWorks 6.5"
!System Software Version 3.3.2.3
!Cut-through mode is configured as disabled
!
configure
stack
member 1 1
exit
ip address dhcp
exit
console#show stack-port 堆叠口现在变为以太网口
Configured Running
Stack Stack Link Link
Unit Interface Mode Mode Status Speed (Gb/s)
---- ---------------- ---------- ---------- ------------ ------------
1 xg1 Ethernet Ethernet Link Up 10
1 xg2 Ethernet Ethernet Link Down Unknown
1 xg3 Ethernet Ethernet Link Down Unknown
1 xg4 Ethernet Ethernet Link Down Unknown
二、Unit2删除堆叠
PC6224-SW1#show run
!Current Configuration:
!System Description "PowerConnect 6248, 3.3.2.3, VxWorks 6.5"
!System Software Version 3.3.2.3
!Cut-through mode is configured as disabled
!
configure
hostname "PC6224-SW1"
stack
member 1 1
member 2 2
exit
switch 2 priority 11
ip address dhcp
exit
PC6224-SW1#show switch 因为管理单元已移除，所以unit 2变为管理单元
Management Standby Preconfig Plugged-in Switch Code
SW Status Status Model ID Model ID Status Version
--- ---------- --------- ------------- ------------- ------------- -----------
1 Unassigned PCT6224 Not Present 0.0.0.0
2 Mgmt Sw PCT6248 PCT6248 OK 3.3.2.3
PC6224-SW1#show stack-port 因为前面已在管理单元上将所有堆叠口改为ethernet口，所以下面显示没有stack口了
Configured Running
Stack Stack Link Link
Unit Interface Mode Mode Status Speed (Gb/s)
---- ---------------- ---------- ---------- ------------ ------------
2 xg1 Ethernet Ethernet Link Down Unknown
2 xg2 Ethernet Ethernet Link Down Unknown
2 xg3 Ethernet Ethernet Link Down Unknown
2 xg4 Ethernet Ethernet Link Down Unknown
PC6224-SW1#delete startup-config
注意，删除配置并不能完全删除堆叠相关配置，这条命令并非必须，也可以采用删除堆叠相关命令，然后保存配置的方法来删除堆叠。
Delete startup-config (Y/N)?y
PC6224-SW1#configure
PC6224-SW1(config)#no switch 2 priority
PC6224-SW1(config)#stack
PC6224-SW1(config-stack)#no member 1
PC6224-SW1(config-stack)#exit
console(config)#switch 2 renumber 1
All the switches in the stack will be reset to perform Manager unit renumbering
and the configuration of Manager switch interfaces will be cleared.
Are you sure you want to renumber? (y/n)y
交换机会自动重启
PC6224-SW1#show switch 只剩一台交换机
Management Standby Preconfig Plugged-in Switch Code
SW Status Status Model ID Model ID Status Version
--- ---------- --------- ------------- ------------- ------------- -----------
2 Mgmt Sw PCT6248 PCT6248 OK 3.3.2.3
PC6224-SW1#show stack-port 堆叠口变为以太网口
Configured Running
Stack Stack Link Link
Unit Interface Mode Mode Status Speed (Gb/s)
---- ---------------- ---------- ---------- ------------ ------------
2 xg1 Ethernet Ethernet Link Down Unknown
2 xg2 Ethernet Ethernet Link Down Unknown
2 xg3 Ethernet Ethernet Link Down Unknown
2 xg4 Ethernet Ethernet Link Down Unknown
console#show run
!Current Configuration:
!System Description "PowerConnect 6248, 3.3.2.3, VxWorks 6.5"
!System Software Version 3.3.2.3
!Cut-through mode is configured as disabled
!
configure
stack
member 1 2 该交换机是6248，所以类型编号为2
exit
ip address dhcp
exit
说明：删除堆叠只与以下三条命令相关
console(config-stack)#stack-port 2/xg1 ethernet 修改端口工作模式
PC6224-SW1(config)#no switch 2 priority 删除堆叠优先级
PC6224-SW1(config-stack)#no member 1 将另一台member移除
console(config)#switch 2 renumber 1 将本机堆叠序号改为出厂配置的1
这些配置体现在以下标红部分:
PC6224-SW1#show run
!Current Configuration:
!System Description "PowerConnect 6248, 3.3.2.3, VxWorks 6.5"
!System Software Version 3.3.2.3
!Cut-through mode is configured as disabled
!
configure
hostname "PC6224-SW1"
stack
member 1 1
member 2 2
exit
switch 2 priority 11
ip address dhcp
exit
PC6224-SW1#show stack-port
Configured Running
Stack Stack Link Link
Unit Interface Mode Mode Status Speed (Gb/s)
---- ---------------- ---------- ---------- ------------ ------------
|
|
|
所有IT类厂商认证考试题库下载
【新盟教育】2023最新华为HCIA全套视频合集【网工基础全覆盖】---国sir公开课合集
【新盟教育】网工小白必看的！2023最新版华为认证HCIA Datacom零基础全套实战课
原创_超融合自动化运维工具cvTools
重量级~~30多套JAVA就业班全套 视频教程（请尽快下载，链接失效后不补）
链接已失效【超过几百G】EVE 国内和国外镜像 全有了 百度群分享
某linux大佬，积累多年的电子书(约300本)
乾颐堂现任明教教主Python完整版
乾颐堂 教主技术进化论 2018-2019年 最新31-50期合集视频（各种最新技术杂谈视频）
Python学习视频 0起点视频 入门到项目实战篇 Python3.5.2视频教程 共847集 能学102天
约21套Python视频合集 核心基础视频教程（共310G,已压缩）
最新20180811录制 IT爱好者-清风羽毛 - 网络安全IPSec VPN实验指南视频教程
最新20180807录制EVE开机自启动虚拟路由器并桥接物理网卡充当思科路由器
[复制链接]
